What Is Catch Basin?

A home built prior to 1960 and located in the urban areas of the larger cities is likely to have a cast iron lid on a large masonry basin. This basin is called a catch basin. There are many reasons for these large structures but the most common purpose of a catch basin is to separate the various contaminants in the residential sewer system.

In order to protect the system a trap or catch basin has been added to residential properties. The idea is; the laundry, floor drains, and kitchen sinks are the most likely origin of the contaminated water.The toilets and bathrooms would discharge directly into the sewer and NOT through the catch basin.When the discharge enters the catch basin it would naturally separate.The solids would sink to the bottom.The gears scum and soap will float on the top.If the outlet pipe has a small elbow or bend it will only allow clean liquid to migrate out to the sewer system.

If the water levels are allowed to become unbalanced or too high the system will not work properly.This is typically because the scum layer is too high.There is an older term called a muck bucket.This is a small shovel or bucket on a pole.It was used to help clean out the scum or other debris accumulated at the bottom of the basin.The modern repair would be to have a sanitary vacuum truck clean out the system. One is suitable to be located in a driveway and strong enough to support the weight of a vehicle, while the other is only for the yard or sidewalk.

What is meant as a catch basin?

1 : a cistern located at the point where a street gutter discharges into a sewer and designed to catch and retain matter that would not pass readily through the sewer. 2 : a reservoir or well into which surface water may drain off.

What is catch basin used for?

A: A catch basin or storm drain is a curbside drain with the sole function of collecting rainwater from our properties and streets and transporting it to local waterways through a system of underground piping, culverts and/or drainage ditches. Storm drains can also be found in parking lots and serve the same purpose.

What is a catch basin and how is it used?

A catch basin is a large drain, usually placed in low areas of a yard, to catch surface runoff water. It usually consists of surface drain that leads to an enlarged box beneath that is then tied to an underground drainage system that finally leads to downspout drains or storm sewers.

How does a catch basin work?

A catch basin has a grate on top and a drainage pipe that slopes away from the basin. This box is set into the ground at a low point on the property. Catch basins help maintain proper drainage and catch debris, which helps prevent pipes downstream from becoming clogged. Water and solids enter the box through the grate.

Winter is fast approaching, which means it is time to take care of those last minute outdoor maintenance projects at your commercial or industrial property. Most property owners neglect to have their catch basins cleaned and inspected on a regular basis. This is typically due to the fact that most of us do not give catch basins a second thought. They are just something in the ground that drains water. That being stated, catch basins do perform an incredibly important function.

Does your front yard look like a marsh after it rains? A catch basin might be the answer. Not only do catch basins keep up your curb appeal, but they can also redirect water away from the foundation of your house. Lets go over some basicswhat are catch basins, where and why are they installed, how do they work, and what do you need to do to maintain them?

Standing water anywhere on your property can cause all kinds of issues. Whether it’s in your yard, driveway, back patio, or near your foundation, you want to get that water moving and away from your house. Catch basins are a great way to do that.

Without catch basins, you can have standing water in your yard, or be at an increased risk of flooding in your home. Properly installed catch basins should be able to move large volumes of water, quickly, even during a heavy rainstorm.

Improved Landscaping – Having pools of standing water, or even perpetually soggy soil can lead to insect growth, plants and trees that brown or die due to too much water, and mold or mildew growth which can eat away at roots and emit foul odors. Potential buyers that see properly installed drainage systems can feel much more confident that they are getting a good value in their future home. People sometimes use the terms interchangeably, but catch basins and french drains are two different systems.

It is normally not necessary to have these drain systems below the frost line because if they are installed correctly water will flow out of them fairly quickly. Installation – It is important that your catch basins are placed on a compact, solid surface, and that they are level so that water flows into them correctly. It is also important to have them just slightly lower than the ground surrounding them so that water won’t build up around the edges and end up flowing under the drains and eroding the soil around them.

What is a Catch Basin?

A home built prior to 1960 and located in the urban areas of the larger cities is likely to have a cast iron lid on a large masonry basin. This basin is called a catch basin. There are many reasons for these large structures but the most common purpose of a catch basin is to separate the various contaminants in the residential sewer system.Before we talk about catch basins we need to talk about the sewer system. Most older systems in older communities have a single pipe system. This system has both the sanitary and the storm sewers go through the same pipes to the same discharge locations. Modern communities and designs utilize a two pipe system, where the storm water is in one pipe and the sanitary sewer in another. The storm water would discharge to an appropriate location like a river or a lake, while the sanitary will terminate in some form of sewage treatment facility.Older treatment facilities did not have the capacity or design ability to fully treat some of the grease, lye, and phosphates created from residential waste. Modern treatment facilities have the ability to treat these elements. In order to protect the system a trap or catch basin has been added to residential properties.

How is a Catch Basin Designed?

A catch basin is typical crafted from masonry. This masonry could be brick, concrete block or concrete rings. It is constructed deep enough to be lower than the bottom of the sewer system in the street, by a few feet. There are at least two pipes installed through the walls of the basin. One pipe is the inlet pipe from the home and the other is the outlet pipe toward the sewer. There may be other pipes as well. These could be the downspouts from the gutters or yard drains.The idea is; the laundry, floor drains, and kitchen sinks are the most likely origin of the contaminated water. The toilets and bathrooms would discharge directly into the sewer and NOT through the catch basin. When the discharge enters the catch basin it would naturally separate. The solids would sink to the bottom. The gears scum and soap will float on the top. If the outlet pipe has a small elbow or bend it will only allow “clean” liquid to migrate out to the sewer system.If the water levels are allowed to become unbalanced or too high the system will not work properly. This is typically because the scum layer is too high. There is an older term called a “muck bucket.” This is a small shovel or bucket on a pole. It was used to help clean out the scum or other debris accumulated at the bottom of the basin. The modern repair would be to have a sanitary vacuum truck clean out the system.Because this system is installed to the laundry and the kitchen there is a strong opportunity for odors. Laundry and kitchen water is extremely malodorous. The installation of a garbage disposal is not encouraged. The organic materials will decay and provide the bad smell in the system.

How is a Catch Basin Inspected?

The inspection of the system should begin with the observations of the exterior elements. You have to verify the lid is safe and intact. Any cracks or damage to the lid can be potentially dangerous. There are two different types of lids.One is suitable to be located in a driveway and strong enough to support the weight of a vehicle, while the other is only for the yard or sidewalk. The driveway lid will be considerably thicker and stronger.The second element to the inspection is to review and look around the line and the concrete ring. This should be without any cracks or displacement. It should also be without any voids. Cracks in the ring can lead to lid failures. Voids or sink holes around the lid can be evidence of sidewall failure and erosions.The interior of the catch basin should be reviewed. Attempt to identify any visible structural deficiencies to the sidewalls, such as visible distortions to the wall. The basin was constructed in a reasonably cylindrical manner. Any deviations to the cylinder should be noted. Next, the water level should be reviewed. The inlet pipe (from the home) needs to be higher than the water level.An inspector should have the ability to determine if the catch basin is still an active part of the sewer system or has been removed from the system and is now vacated. There is a very easy way to determine this: turn on the water in the kitchen and laundry sinks. This water should be visibly discharging into the catch basin. If the water is not draining into the catch basin it is most likely vacated. Make sure to operate the system long enough to verify the system.If the water level is higher than the inlet pipe there is a strong possibility of back up or slow drains in the home. The outlet pipe should be partially submerged in the water with the return under water.

Do Houses Need a Catch Basin?

A catch basin is no longer a necessity in modern homes. The older system can be removed from the system. It is a matter of reconfiguring the drains in the home and possibly adding an ejector system.When a system is taken offline they are typically permanently sealed. This would include filling the basin with an appropriate material. This could include sand, stone, gravel or the combination of all of them. If you need help with other home care issues, be sure to check out our seasonal home maintenance checklist!

What is a Catch Basin?

A catch basin is, in other words, a storm drain. They are used to redirect water in an aim to prevent flooding and are common on public streets but may also be installed on private properties. Catch basins collect rainwater or melted snow, transporting runoff to a sump, reservoir, or treatment facility.

Is Your Storm Drain Clogged?

If you notice that the catch basin or storm sewer is not draining properly, it might need to get cleaned you can call a company like MT Catch Basin to get the catch basin cleaned and inspected.

Catch Basins

Standing water anywhere on your property can cause all kinds of issues. Whether it’s in your yard, driveway, back patio, or near your foundation, you want to get that water moving and away from your house. Catch basins are a great way to do that.A-1 will evaluate your standing water issue and devise a plan for getting that water moving. This typically involves digging a trench and installing a drain and piping to move that water to local waterways, or stormwater systems. Afterwards, the trench is filled in and landscaping and lawn replaced.

What is a Catch Basin?

A catch basin is a large drain, usually placed in low areas of a yard, to catch surface runoff water. It usually consists of surface drain that leads to an enlarged box beneath that is then tied to an underground drainage system that finally leads to downspout drains or storm sewers. The number of catch basin drains, and the extent of the sub-surface drainage system will depend on how much water is to be moved.

Why Catch Basins?

Without catch basins, you can have standing water in your yard, or be at an increased risk of flooding in your home. The key to catch basins is the speed by which they can move the water. Standing water will eventually dissipate into the ground around it, but if that dissipation is too slow, you can have ponds of water that support mosquito growth, or you can have water flowing into your house due to the fact it has nowhere else to go. Properly installed catch basins should be able to move large volumes of water, quickly, even during a heavy rainstorm.

Catch Basin vs. French Drain

The ability to quickly move water off of your property is the primary purpose of a catch basin. This provides several benefits, including:

Why Use A-1 to Install Catch Basins?

This is a quick guide on how catch basins work, and how one will typically be installed.